Security system installation SWMS, drafted for your job
Mounting cameras and pulling alarm cables puts installers above doorways, inside ceiling spaces and beside existing power and moving access equipment. Tell us the security equipment and building: your SWMS is drafted around cable routes, fixing and commissioning, and you check it on site before starting.
A$39per job
However many high-risk activities it covers.
- However many high-risk activities it covers.
- 3 for A$99
- 10 for A$249
- Yearly A$129 for 120
- Monthly A$60 for 10
You review it on site before work starts.
Your Business
Safe Work Method Statement
Version 1
Draft
Security system installation
Site Your site address
Law Your state
High-risk construction work
- Work where someone could fall from height
- Work on or near energised electrical installations
Job steps, hazards and controls
| 1 | Inspect locations and cable routes | Hidden services and suspect building materials | High | Locate services and check wall and ceiling construction |
| 2 | Set up protected mounting access | Falls and people passing beneath cameras | Extreme | Use a stable platform and separate the area below |
| 3 | Run security cables | Fragile ceilings and drilling dust | High | Use supported routes and extraction at masonry entries |
| 4 | Mount and connect security devices | Dropped equipment and electrical supplies | High | Support devices and isolate supplies during connections |
| 5 | Commission alarms and access controls | Unexpected gate or door movement | High | Clear travel areas and test safety functions before handover |
Illustrative first page. Yours carries your business name only.
What you get
What your security system installation SWMS will contain
An A4 document your crew can read on site, a PDF for the builder and a sign-on register.
- Job and site detailsYour business, the site, the principal contractor, the dates.
- High-risk construction workThe categories your job involves, ticked.
- Step-by-step methodEach step with its hazards, risk rating and controls.
- How controls are checkedWho puts each control in place, monitors and reviews it.
- PPE, plant and permitsEquipment and training the job needs.
- Emergency planAssembly point, first aid, nearest hospital to confirm on site.
- Consultation and reviewWho was consulted, when it is reviewed.
- Sign-on registerYour crew signs by QR or on paper.
High-risk construction work
Categories this task often involves
You tick the ones your job involves. Each ticked category gets its own steps and controls, in your state's wording.
- Work where someone could fall from height
- Work on or near energised electrical installations
State notes
Rules depend on your state
Pick your state when you start. Your state's regulator publishes the rules and guidance for this work.
Hazards and controls
What goes wrong on a security system installation job, and how the SWMS controls it
These rows are written for this task. Your draft adds the ones your site and method need.
- 1
Falls while reaching to mount CCTV cameras above building entrances
Extreme- Use a stable protected work platform positioned for the camera fixing points
- Keep entrances below separated and move the platform rather than overreaching
- 2
Drilling into concealed electrical cables at alarm and camera fixing points
Extreme- Locate services and mark drilling routes before fixing security devices
- Arrange isolation where drilling could reach wiring and stop at uncertain cable paths
- 3
Falls through ceilings while routing security cables above occupied rooms
Extreme- Use supported roof space access and keep weight off ceiling linings
- Provide lighting and route cables from protected positions where practical
- 4
Dust from drilling masonry and suspect wall linings for security cable entries
High- Identify wall materials before drilling and stop for assessment of suspect linings
- Use suitable on-tool dust extraction and keep other trades outside the drilling area
- 5
Cameras or control panels falling while brackets are being secured
High- Use holding aids or supported positioning until brackets and equipment fixings are complete
- Keep people clear below and avoid supporting equipment by loose cables
- 6
Doors or powered gates moving during access control commissioning
High- Isolate movement during wiring and clear the gate or door travel area before testing
- Use controlled test sequences and stop if sensors or safety devices do not respond
- 7
Electric shock from mains supplies inside alarm and access control cabinets
Extreme- Isolate the supply and arrange electrical connection work by an electrical worker
- Keep low power cabling separate and verify isolation before cabinet work
How the job usually runs
- 1Inspect locations and cable routesHidden services and suspect building materials → Locate services and check wall and ceiling construction
- 2Set up protected mounting accessFalls and people passing beneath cameras → Use a stable platform and separate the area below
- 3Run security cablesFragile ceilings and drilling dust → Use supported routes and extraction at masonry entries
- 4Mount and connect security devicesDropped equipment and electrical supplies → Support devices and isolate supplies during connections
- 5Commission alarms and access controlsUnexpected gate or door movement → Clear travel areas and test safety functions before handover
PPE for this job
- Safety boots
- Safety glasses
- Handling gloves
- Hearing protection for drilling
- Fitted particulate respirator for dusty drilling
- Safety helmet for overhead installation
- Fall protection equipment where selected access needs it
Your draft lists the PPE your site and method need.
After you finalise
Brief your crew and send it to your builder
Crew signs by QR
Send to my builder
PDF and register
Builder sent it back?
Make their changes and re-issue the same job free. Workers re-sign the new version.
Questions
Security system installation SWMS questions
- Last reviewed
- 21 October 2026
- How
- Hazard rows checked against the task; no legal line is stated unless it is logged from primary text.
- Next review
- Every six months, or when the method or rules change
Does it cover CCTV cameras and alarm cable runs in ceiling spaces?
Yes. Describe the mounting positions and cable routes. The draft covers protected camera access, supported movement above ceilings, concealed service checks and separating drilling work from building users.
Can it include testing an access controlled powered gate?
Yes. Describe the gate and control changes. The draft covers isolating movement during connection, clearing the travel area for testing and stopping commissioning if sensors or safety devices do not respond.
How much does a security system installation SWMS cost?
One job uses 1 SWMS when you finalise: A$39 for one, however many high-risk activities it covers. AI drafting needs a SWMS pack or plan. Packs and Yearly cost less per SWMS.
Is this a template?
No. You describe the job and the site, and the SWMS is drafted for them. You edit anything, then finalise it.
Who checks the SWMS?
You do, with your crew, on site before work starts. The draft gives you a strong starting point; the person running the work makes sure it matches the site.
My builder sent it back. What now?
Open it, make the changes they asked for and re-issue it. Corrections to the same job are free.
How does my crew sign it?
Show the QR code on your phone or print the A4 sign-on sheet. Workers read and sign on their own phones without an account.
Does it work in my state?
Yes. You choose the state before drafting, and the document names the law that applies there. Victoria uses its OHS Regulations.
Related
Related SWMS
